inserted tool是什么意思

网络释义

用法例句

The cemented carbide tool coated with diamond film is one of the important application of CVD diamond film.

金刚石薄膜涂层硬质合金刀具是CVD金刚石薄膜的重要应用领域之一。

The Co concentration in the etching liquor after different acid corroding time for YG series cemented carbide tools was tested by atomic absorption spectrometry,the hardness change of tools was detected by HRC and the microstructure of diamond film was observed by scanning electron microscope.

采用原子吸收光谱(AAS)标准曲线法对YG系列硬质合金刀具酸蚀后浸蚀溶液中的Co浓度进行了定量测试;采用洛氏硬度(HRC)计跟踪测试了不同酸蚀时间后刀具硬度的变化;采用扫描电子显微镜(SEM)观察了硬质合金刀具酸蚀前后的组织变化及金刚石薄膜的组织形貌。

Based on the high-speed milling experiment for titanium alloy Ti6Al4V with fine grain cemented carbide tool Y330,the tool wear and breakage modes and failure mechanisms were analyzed.

基于用Y330细晶粒硬质合金刀具高速铣削Ti6Al4V钛合金的试验,分析了刀具的损坏形态和失效机理。

The diamond film was deposited on WC-6%Co(mass fraction) cemented carbide by DC arc discharged plasma chemical vapor deposition.

低压气相金刚石薄膜硬质合金刀具在直流弧光放电等离子体CVD镀膜设备上制备。

The contrast dry cutting experiments are carried out to study the cutting performance of Ni based PM parts by using ceramic and cemented carbide cutting tools.

对陶瓷刀具和硬质合金刀具进行了镍基粉末冶金零件的干切削对比试验,测量了切削力和加工表面粗糙度,分析了刀具的磨损机理。

Take difficult-to-cut materials and carbide cutting tools as the research objects, aim at each cutting character, using Rule-based-Reasoning, establish a cutting tools material intelligent selection system which is based on Visual C++6.

以难加工材料和硬质合金刀具为研究对象,针对它们各自的切削加工性,利用基于规则(RBR)推理方法,以Visual C++ 6。

The percentage lf carbide cutting tools consrmed by the world at 2003 and the fast increasing of carbide gear hob was analyzed.

分析了2003年硬质合金刀具在全世界刀具消费值中的比例,及硬质合金齿轮滚刀的迅速发展。

This paper analyzed the changes of Japanese carbide cutting tools in 2003,and the influence of Japanese mould & IT industry on these changes.

分析了2003年日本硬质合金刀具销售值占刀具总销售值的比例,及硬质合金立铣刀的迅速发展。

Aiming at to the question that sticking of cutting tool is serious when using the hard alloy cutting tools to cut austenite non-corrosive steels,this article uses the DICTRA module in thermodynamic software thermoCalc to simulate the atom diffusion between the hard alloy cutting tools and cut work-piece.

针对硬质合金刀具切削奥氏体不锈钢粘刀现象严重的问题,利用热力学软件Thermo-Calc中的TCC模块和D ICTRA模块,模拟了硬质合金刀具与被切削工件之间发生的原子扩散。

In dry cutting conditions within single-factor test,comparative analysis the difference of the PCBN cutter and hard alloy cutting tools milling GCr15 steel.

在干式切削的条件下,采用单因素试验法,比较分析了PCBN刀具和硬质合金刀具铣削轴承钢GCr15的差异。

manufacturing technique of rare-earth hard alloys tool

稀土硬质合金刀具制造技术

Influence of Chip-breaker Structure of Carbide Cutters on Chip

硬质合金刀具槽型结构对切屑的影响

The Study on Electropolishing of WC-Co Cemented Carbide;

YG类硬质合金刀具电解抛光的研究

Application of Carbide Cutting Tools in the World at 2003;

2003年全球硬质合金刀具产销情况分析

The Changes of Japanese Carbide Cutting Tools in 2003;

2003年日本硬质合金刀具的变化

Oxidation Resistance of Cemented Carbide Tools

硬质合金刀具材料的抗氧化性能研究

Wear Mechanism of Cemented Carbide Tool in High Speed Machining Iron-based Superalloy GH2132

高速车削铁基高温合金硬质合金刀具磨损机理

Friction wear behavior of diamond-like carbon films on carbide cutting tool

硬质合金刀具类金刚石涂层的摩擦磨损性能

The Study of the Principle and Countermeasure of Colbat Exposure in Cemented Carbide Tools;

硬质合金刀具钴元素浸出机理及对策研究

Research on Sintering Technology of Nanostructured WC-10Co Hardmetal;

纳米WC-10Co硬质合金刀具材料烧结技术研究

The Current Situation and Development Trend of Solid Carbide Tools;

整体硬质合金刀具的产业现状与发展趋势

Development and Study of CAD System for Solid Carbide Cutting Tools

整体硬质合金刀具CAD系统的研究与开发

Effects of C-ion Implantation on Properties of TiN Coatings on Carbide Tools

C离子注入对硬质合金刀具TiN涂层性能的影响

Preparation and Cutting Performance of YT15 Cemented Carbide Tools with ZrN Coating

ZrN涂层YT15硬质合金刀具的制备及切削性能

Research on Tool Wear in Machining Cast Iron MT-4 Using Carbide Tool

硬质合金刀具YT15切削铸铁MT-4的磨损研究

Study on Preparation Technology for ZrN Coating of YT15 Cemented Carbide and the Cutting Performance

ZrN涂层YT15硬质合金刀具的制备与切削性能研究

indexable carbide insert cutting tool

硬质合金可转位刀具

Heavy duty carbide insert blanks for cutting tools

GB/T14446-1993重型刀具用硬质合金刀片毛坯