pin gear是什么意思

网络释义

用法例句

Transmission efficiency of powder metallurgy helical gear system;

粉末冶金斜齿轮传动效率研究

Simultaneous-control model for hobbing of noncircular helical gears;

非圆斜齿轮滚切加工的联动控制模型

Multi-objective optimization design of the bevel wheel based on QPSO;

基于量子粒子群优化算法的斜齿轮设计

Application of QPSO Algorithm Based on Evaluated Selection to Multi-Objective Optimization Design of the Bevel Wheel

基于评估选取的QPSO算法在斜齿轮多目标设计中的应用

It presents the method of measuring manufacturing precision of bevel cylindrical gear by the three dimensional coordinate meter,that is,measuring three dimensional coordinate values of bevel gear profile by the three dimensional coordinate meter,and analysing the data of coordinate values by the method of least squares,obtaining gear profile errors of bevel.

给出用三维坐标测量仪测量斜齿圆柱齿轮制造精度的一种方法,即用三维坐标测量仪测量斜齿轮轮廓曲面的三维坐标值,根据最小二乘法对该坐标值进行数据分析,得出斜齿轮齿廓曲面的齿形误差。

This paper studies the bevel gear slotting numerical control technology on base of DSP chip,and raises the point of view that use virtual axis interpolation technology and use software to realize the electronics gear differential technology.

国内斜齿轮加工一般采用滚齿机或者进口插齿机,由于产品体积过大和机床价格昂贵而受到限制。

Set up a method to calculate helicao gears meshing stiffness according to the comparability between straight gears and helical gears based on knowing the meshing stiffness of straight gears.

从直齿轮和斜齿轮数学模型的相似性方面入手,提出一种在已知直齿轮啮合刚度的基础上,确定相应斜齿轮啮合刚度的方法。

This paper has studied the approaching method of helical gears.

本文在新研制的砂轮修整器上 ,对斜齿轮的成形磨削逼近法进行了研究。

spur and helical hobbing machine

正齿轮和斜齿轮滚齿机

cross helical gear

螺旋齿轮, 交错斜齿轮

The four main types of gears (spur, helical, worm, and bevel)and a rack and pinion are shown in Figure 7.

图7所示是四种主要的齿轮（巨齿轮，斜齿轮，蜗轮和伞齿轮）以及齿条和小齿轮。

bevel gear:Either of a pair of gears with teeth surfaces cut so that they can connect unparallel gear shafts.

斜齿轮:用以连接不平行齿轮轴齿轮的任一对齿面切削。

The Engaging Load and Axial Modification of Helical Gear Used in Increasing Gearbox of Wind Turbine Generator;

风机增速器斜齿轮啮合载荷及齿向修形的研究

Finite Element Contact Analysis of Helical Gears with Surface and Shaft Deviations

考虑齿面及轴线偏差的斜齿轮接触有限元分析

Optimizing Design of the Planetary Helical Gear Based on Minimum Flash Temperature of Tooth Surface

基于齿面闪温最低的行星斜齿轮优化设计

Tooth root stress analysis of involute helical gear based on ANSYS

基于ANSYS的渐开线斜齿轮的齿根应力分析

The helical gear has become worked down over the years.

斜齿轮因为年久而磨损了。

The research and application of contact trace of crossed helical gear pair

交错轴斜齿轮副接触迹的研究与应用

BEM for 3-D Elastic Deformation Analysis in a Cylindrical Helical Gear

圆柱斜齿轮三维弹性变形的边界元法

Basic tooth profile of straight and skew bevel gears

GB/T12369-1990直齿及斜齿锥齿轮基本齿廓

Analysis of Skewed Tooth Bevel Gear and Straight Tooth Bevel Gear

斜齿圆锥齿轮与直齿圆锥齿轮应力分析研究

3-D Finite Element Vibration Analysis of Helical Gears

斜齿圆柱齿轮的三维有限元振动分析

Study on the Meshing Principle of Three-freedom Straight and Inclined Gear;

三自由度直、斜齿齿轮啮合机理的研究

APDL Parametric Solid Modeling of Skew Bevel Gear Based on ANSYS

基于ANSYS的斜齿锥齿轮APDL参数化建模

Multi-target optimization design of the Helical gears drive

斜齿圆柱齿轮传动的多目标优化设计

Parametric Design of Standard Involute Helical Gears Based on Pro/E Wildfire

基于Pro/Engineer标准渐开线斜齿圆柱齿轮参数化设计