ultimate shear stress是什么意思

网络释义

用法例句

FEM analysis of the distributions of maximum shear stress in coating system with TiN/Si 3 N 4 double coating layers indicated that the distribution of maximum shear stress is better if the material with relatively low Young's modulus used as the surface layer.

采用有限元数值计算方法,模拟分析了TiN、Si3N4的双层涂层与GCr15基体体系中的最大剪应力分布。

Based on the shear stress analysis on the different locations of the asphalt pavement structure,the paper obtains the distribution characteristics and rules of maximum shear stress under different depths of the pavement.

通过对沥青路面面层内不同位置的剪应力分析,得出了不同深度最大剪应力的分布特点及不同深度最大剪应力的分布规律。

The analysis shows that maximum shear stress which come into surface-initiated under wheel load is beyond shear strength of asphalt binder.

计算结果表明,在假定的车轮荷载作用下,路面结构最大剪应力发生在路面表层,位置在轮迹边缘,其大小接近或超过常温下沥青混合料的抗剪强度,是导致半刚性路面产生TDC的主要原因。

Through the experimental results and study on the reason of fracture,we considered that mean stress and maximum shearing stress were different in tension and compression,condition of fracture was proposed.

提出了考虑平均应力和最大剪应力共同影响、考虑了拉压异性的脆断条件。

3, the distribution of maximum shearing stress under coating surface is rather beneficial for enhancing the fatigue life of bearings, whereas ratio t/a equ.

3时 ,表面下的最大剪应力分布对提高轴承疲劳寿命较为有利 ;t/a =0 。

To achieve easily and rapidly the key data of the yield shear stress and ultimate shear stress,the double-hole micro-shear,transistors and microchip machine MSP430F149 are used in the testing system.

通过双孔微剪切法、传感器和MSP430F149单片机,快速方便地获得材料的屈服剪应力、最大剪应力数据。

The maximum shear stress and the maximum tensile stress on the coating and substrate interface were analyzed.

通过对涂层与基体界面最大剪切应力和最大法向应力的分析,比较了模型中不同基体台阶深度、涂层尺寸对界面结合强度的影响。

Draw the element for maximum shear stress and mark values of all stresses.

画出最大剪应力的单元体并标出全部应力值。

In developing equations for maximum shear stresses, the special case will be considered.

在导出最大剪应力表达式时，将考虑一种特殊情况。

maximum shear stress yield criterion

最大剪切应力屈服条件

critical shear strain energy theory

最大剪应变能量理论

The application of shear wall structure steel large formwork construction technology

剪力墙结构钢制大模板施工技术应用

Cohesion is best defined in terms of the plot of shear stress versus normal stress given in Figure 9.

粘结力最好根据图9中剪切应力和法向应力的关系曲线确定。

stress-controlled direct shear apparatus

应力控制式直接剪力仪

Study of Shear-lag and Distortion for Thin-Walled Curved Grider with Great Initial Curvature;

大曲率薄壁曲线箱梁剪力滞及畸变效应研究

Analysis on Seismic Response of the Shear Wall Structure with Large Spaces at Lower Part;

底部大空间剪力墙结构的地震响应分析

Localization of large moulding board in construction of puncheon shearing force wall;

大模板在短肢剪力墙工程施工中应用的局限性

Investigation of Shear Lag Effect of Continuous Steel Box Girder Bridge with Great Width-to-Span Ratio

大宽跨比连续钢箱梁桥的剪力滞效应研究

Model for analyzing seismic response of RC shear/core wall structure under major earthquakes

大震下RC剪力墙(筒体)结构地震反应分析模型

The additional shear and normal stress of fiber become large with the addition of the contract ratio.

纤维附加剪应力和附加正应力差随着收缩比的增大而增加。

You had need to do your best.

你应当尽最大的努力。

angle for maximum righting lever

最大复原力臂对应角

octahedral shearing-stress plasticity condition

八面体剪应力塑性条件

the shear changed the quadrilateral into a parallelogram.

外力使物体发生剪应变。

Friction and cohesion are best defined in terms of the plot of shear stress versus normal stress given in Figure 9.

摩擦角和粘结力最好是根据图9中剪切应力和法向应力的关系曲线确定。