Pusey and Jones indentation instrument是什么意思

网络释义

用法例句

The Leeb hardness tester as well as its features,typical applications,development and proper type selection were introduced.

介绍了里氏硬度计及其特点与适用场合,里氏硬度计的发展状况,里氏硬度计的正确选型;通过分析影响里氏硬度计测试精度的各种因素说明了如何正确使用里氏硬度计,并简要介绍了里氏硬度计的通用维护手段。

Using G type Leeb hardness tester to test the hardness of low strength structural steel sheets, the hardness number is often lower.

针对用便携G型里氏硬度计对低强度钢板测试其硬度值偏低的现象 ,利用静载台式硬度计及动载里氏硬度计对高强度不锈钢板和低强度结构钢板进行了测试 ,并进行了对比分析。

Combining with the situation of existing error in hardness measurement by Leeb Hardness Tester,this paper introduces the measuring principle of leeb hardness tester and analyzes the influencing factors of measuring error such as surface roughness of specimen,specimen thickness and the distance between measuring points,and proposes some corresponding preventive measures.

结合基建现场利用里氏硬度计测量硬度过程中存在误差的情况,介绍里氏硬度计的测量原理,分析影响里氏硬度计测量误差的试件表面粗糙度、试件厚度和测量点的距离等因素,并提出相应的预防措施。

Using the cone anvil made by self, inspect the hardness of small steel ball on WELSON - A653T Rockwell hardness tester ,solve the problem of the small steel ball is slip on the pedestal anvil and "V" shape anvil, difficult to fix,and make the variance analysis to the result compare with traditional method,and to prove the result , of inspect by this way is correct.

在WELSON—A653T洛氏硬度计上,采用自制凹锥形砧座测试微小钢球的硬度,解决了微小钢球在常用平面砧座和V形砧座上易打滑,不易固定,致使压头打在砧座上,损坏压头和砧座的难题,并采用方差分析的方法,将该法与传统试验方法相比较,验证其检测结果与传统法所获检验结果无显著性差异。

The Rockwell hardness tester is a precision measurement instrument in material and part hardness testing, which is often used in detection of materials, product and half-finished product.

洛氏硬度计是检测材料和零件硬度较精密的计量仪器,用来测量材料或者成品半成品的相应硬度,其性能指标主要体现在检测精度和操控性两个方面。

The text particular introduced working principle of Rockwell hardness tester, designed load-up program, analyzed raliability,and according related requirements elected electromechanical and the like components.

传统洛氏硬度计采用杠杆加载,压头多在侧向用紧定螺钉顶紧,长期使用很难保证精度,且需要操作人员的经验和技巧。

INFLUENCE OF THE ON-THE-SPOT FACTOR ON MEASUREMENT VALUE OF RICHTER SCALE SCLEROMETER

现场因素对里氏硬度计测量值的影响

The Basic Elements and Malfunction Disposal of Leeb Hardness Tester

里氏硬度计基本原理和常见故障处理

Influence Factors Analysis on Measuring Error Leeb Hardness Tester on Site

现场里氏硬度计测量误差的影响因素分析

Cause of Fastener Hardness Detection Deviation by Portable Leeb Hardness Tester

便携式里氏硬度计检测紧固件硬度偏差原因分析

semi-automatic optical Brinell hardness tester

半自动光学布氏硬度计

automatic digital display Rockwell hard-tester

自动数显洛氏硬度计

quadrant style shore durometer

扇形[指盘]肖氏硬度计

Conversion Relation of Leeb-hardness,Vickers-hardness and Strength of Austenitic Stainless Steels

奥氏体不锈钢里氏硬度、维氏硬度及强度之间的换算关系

Metallic materials--Leeb hardness test

GB/T17394-1998金属里氏硬度试验方法

pulfrich photometer

普尔弗里希氏光度计

Bonded abrasives hardness measurement by Rockwell tester

GB/T2491-1984洛氏硬度计检验磨具硬度的方法

Specifications for Rockwell hardness testers

GB/T2848-1992洛氏硬度计技术条件

Specifications for Vickers hardness testers

GB/T7664-1987维氏硬度计技术条件

Specification for Rockwell superficial hardness testers

GB/T3773-1993表面洛氏硬度计技术条件

Verification of Brinell hardness testers

GB/T6269-1997布氏硬度计的检验

Verification of vickers hardness testers(less than HV 0.2)

GB/T17198-1997维氏硬度计(小于HV0.2)的检验

The Common Maltfunction and Settlement about the Control Mechanism of Brinell′s Hardness Tester

布氏硬度计控制机构常见故障及处理

The Development of Inspection and Control System Used in Brinell Hardness with SCM

布氏硬度计的单片机测控系统的研制