run-out of shaft是什么意思

网络释义

用法例句

Based on the data of measured fluctuating pressures, cavitation noise, air entrainment, main shaft runout of the turbine and dewatering inspection of it afterward, the hydraulic stability of the turbine No.

根据原型实测动水压力、空化噪声、补气、大轴摆度及水轮机检查等成果,研究了水轮机水力稳定性。

Treatment to vibration and shaft oscillation of hydro-generator set of Doulingzi Hydropower Station

陡岭子水电站机组振动与大轴摆度的处理

"When the two shafts are at an angle to each other, the bearings in the yokes permit the yokes to swing around on the trunnions with each revolution."

当两轴相互处在同一角度上,主动轴转动时万向节叉上的轴承使万向节叉绕万向节十字轴摆动。

The maximum absolute value of a periodic curve measured along its vertical axis.

振幅沿垂直轴摆动的周期性曲线的最大绝对值

AAA Bearing LTD offers Offers to Tapered roller bearings, thrust ball bearing and Self-aligning bearing.

公司提供大量的摆动轴承、自动调心轴承和夹紧套筒。

When swinging drive mechanical operation, such as the rotation speed of the force to make efforts axial shaft before and backward rotation and enable higher plane.

当摇摆传动机械运作时，等速度的旋转入力轴使出力轴向前和向后旋转，并使平面升高。

Function of Thighs’ Actively Swinging Forward to Increase the Dash Speed

大腿积极前摆对提高短跑速度的作用

Rocket frame positioning accuracy testing for NC summer beam milling machine

数控飞机大梁铣床摆架定位精度检测

The Research on Equal-strength Design of Large-scale Heavy-load Cross-shaft Universal Clutch

大型重载十字轴式万向联轴器等强度设计研究

Skirt Marker: for marking hem lengths accurately. Markers are available for use with chalk or pins.

裙摆标示器：用于精确地标示裙摆的长度,可与画粉或大头针一起用。

Attitude control is obtained by gimballing the engine up to ±7 degrees.

姿态控制是由发动机摆动而得到的，摆动度最大为±7°。

Determining the Acceleration of Gravity with Simple Pendulum

用单摆测重力加速度——一摆球的大小对测量结果的影响

An elephant walks like this and that.

大象摇摇摆摆地走着。

Treatment on throw and runner cracks of hydro-power plant

水电机组摆度增大和转轮裂纹的分析处理

Excitations of Chandler Wobble by the Pacific,Indian and Atlantic Oceans during 1980-2005

太平洋、印度洋和大西洋对Chandler摆动的激发,1980—2005

The Development of Temperature Measuring System of Large-Scale Shaft Parts;

大尺寸轴类零件温度检测系统的研制

Casting Technology of High Strength and Thick Section Ductile Iron Mainshaft

高强度厚大断面球墨铸铁主轴的铸造

Output shaft when the swing set in the center of rotation on the trip-down, design may also need to set rotation angles and movements itinerary.

出力轴在摆动时可设定在旋转行程的中心点上停动，也可依设计需要设定旋转角度和升降行程。

The throw of the crankshaft, i.e. the distance between the main journal and the big end centers, controls the length of the stroke.

曲轴的摆幅，即在主要曲颈和连杆大头末端中心之间的距离，控制着冲程的行程。