bamboo wedge是什么意思

网络释义

用法例句

The analysis on heat treatment management and properties of slot wedge in the generator rotor;

发电机转子上槽楔的热处理组织和性能分析

For improveing die design efficiency and quality like slot wedge in micro motor,reducing the labor input,it needs to develop the CAD of die for slot wedge.

为了提高微电机槽楔这类零件模具的设计效率和质量,降低设计人员的劳动强度,需要开发相应的模具CAD系统。

Only changing the nonmagnetic slot wedge,was the pole arc width of one pole changed in this method,and the interval between two adjacent poles was the same.

为了研究实心转子永磁同步电动机的削弱措施,结合永磁电机永磁体极弧系数和永磁体不对称放置的方法,提出了一种仅改变实心转子非磁性槽楔的齿槽转矩削弱方法。

Using magnetic slot wedge to improve the air-magnetic field of brushless direct current motor;

采用磁性槽楔改善无刷直流电机的气隙磁场

The article briefed The category and feafures of magnetic slot wedge,as well as the principle and practical effect of magnetic slot wedge in the energy-saring of generator.

介绍了磁性槽楔的种类和特点,以及磁性槽楔在电机节能方面的原理和实际作用。

This paper is trying to solve the problem of the influence of magnetic slot wedge on the efficiency and load capability of motor and generator.

本文试图从理论上解决磁性槽楔对电机的效率和负载能力的影响问题,并提出了“有截获槽口漏磁通作用的绝缘拼接式磁性槽楔”的方案,既起到抑制齿谐波的作用,又不加大齿间漏磁,而且将原有槽口漏磁和一部分槽坑漏磁引导至气隙,使这些无效磁通转化成有效磁通,从而使电机不但能提高效率和功率因数,而且能提高其负载能力。

Study on acoustic detection of stator slot wedges in large generators;

大型发电机定子槽楔松动的声检测研究

After a long term running of large generator,the stator slot wedges would become loose under electromagnetism force as a result of the compositive effect of stator winding current and the magnetic field across through stator slot.

大型发电机在长期的运行过程中,由于定子线圈的电流与定子槽内横向磁场的作用使得槽部线棒承受相当大的电磁力,定子槽楔长期在机械应力作用下会发生松动现象。

The overhaul procedure of the stator wedge in pumped storage power station is introduced in this paper.

本文详细介绍抽水蓄能机组定子槽楔的结构,大修中发现的径向压紧力下降、部分槽楔出现向下移位、波纹垫条老化等问题及大修的工艺,为抽水蓄能机组的定子槽楔大修进行了经验总结。

An on\|site test was performed through the acoustic detection system to detect stator wedge looseness in a generator.

本文将声学技术应用于大电机定子槽楔松动的无损检测中,研制出一套数字化声学检测系统,对发电机定子槽楔的松紧状态进行现场实测。

In this paper,a physical model,thin plate resonator model,is proposed and analyzed based on the thin plate theory to investigate the acoustic signal response of the loose stator wedge to an impact.

基于薄板理论 ,建立并分析了电动机定子槽楔松动后的物理模型 ,薄板声谐振子模型。

Study on acoustic detection of stator slot wedges in large generators

大型发电机定子槽楔松动的声检测研究

Elasto-plastic Analysis of the Rotor and Wedges of 1000MW Supercritical Turbogenerator

超临界1000MW汽轮发电机转子和槽楔的弹塑性分析

Development of Pultruded Magnetic Slot Wedge Based on Glass Fibre Reinforced Unsaturated Polyester Resin

玻璃纤维增强聚酯树脂引拔磁性槽楔的研制

Application of Magnetic Slot Wedge in Y2 Series High Voltage Asynchronous Motor

磁性槽楔在Y2系列高压电动机中的应用

Generator Stator Wedge Replacement and Analysis of Core Corona Corrosion Treatment

发电机定子槽楔更换及铁芯电晕腐蚀处理浅析

A detecting system of stator wedges in large generator based on DSP

基于DSP的大型发电机槽楔松动检测系统

The loosening and dropping out of slot wedges may damage insulation of rotor and stator to cause stator insulation breakthrough.

槽楔松动脱落可能划伤转子绝缘和定子绝缘,造成定子线棒主绝缘击穿。

Study on Effect of Symmetry of Wedge-shaped Cutting Hole Angle on Cut Blasting

楔形掏槽炮孔角度对称性对掏槽效果影响研究

Thin taper keys and their corresponding keyways

GB/T16922-1997薄型楔键及其键槽

Taper keys--Cross section dimensions of keys and keyways

GB/T1563-1979楔键键和键槽的剖面尺寸

A wedge or key that fits into a groove to make a joint.

加强肋作为连接物填入槽内的楔形物或舌状物

Preliminary Study on Forming Laws of Cuspidal Splitter Split-extruding Rectangular Slot

尖头劈楔劈挤矩形槽成形规律初步研究

Popularization and Application of Deep-hole Blasting Technique in Bottom Compound-term Wedge Cutting

底部复式楔形掏槽中深孔爆破技术的推广应用

Design of Combination of Smooth Blasting and Double-wedge Cut for Roadway Excavation

双楔形掏槽方法和光面爆破技术的综合设计

The loosening holes outside the plough cut are also drilled at an angle which improves the breakage possibility.

在楔形掏槽眼外侧的扩槽眼也要有角度以改善爆破效果。

The Norwegian cut can provide more dependable advance per round than the plough cut.

挪威掏槽与楔形掏槽相比，可以提供更可靠的每次爆破的进度。

The surface of inclined wedge pushes the triangle side of the waste and makes the plate move ahead, thus meeting the requirement of position setting and feeding the plate automatically.

斜楔插板上的斜楔面推动废边的三角槽一侧，使板料向前运动，达到板料定位和自动送料的目的。

a screwdriver with a flat wedge-shaped tip that fits into a slot in the head of a screw.

有可以插入螺丝头的狭槽的楔形尖端的螺丝起子。