The shearing resistance was tested at different rotary speeds.
采用复合搅拌摩擦点焊的方法对2mm LF21铝合金薄板进行焊接,测试了不同旋转速度下的焊接接头的抗剪力,并观察和分析了点焊接头的成形及微观组织。
The experiment used electrode with different rotation speed to process deep-small holes,and collected the time data during the whole process,after this more of the processing curves could be formed.
采用不同旋转速度的电极进行电火花深小孔加工,通过采集加工时间数据,得到多条加工曲线。
The influence of tool rotation speed and the match of tool rotation speed with welding speed on the FSW joint morphology of 6063 aluminum alloy and its mechanical properties is studied.
研究了旋转速度以及旋转速度与焊接速度的匹配对6063铝合金搅拌摩擦焊接头形貌以及力学性能的影响。
At the symmetrical axis of the fire,when the rotation rate is less than 78 r·min-1,the temperature of a fire whirl raised with higher rotation speed;when the rotation is more than 78 r·min-1,the temperature decreased with elevated rotation speed.
结果表明,旋转火焰内部的燃烧温度分布不仅与火焰的旋转速度有关,而且与燃烧产物的含量存在很大的关系。
maximum bridge speed control
驾驶室最大转速控制
Incorrect idle or maximum speed
怠速或最大转速均不正常
Max.Spin Speedrpm)
最大脱水转速转/分钟
Max. Spin Speed: 100rpm
最大脱水转速: 100转/分钟
maximum momentary speed variation
最大瞬时转速变化率
This engine can produce powerful torque power with relative low speed.
相比较低转速输出强劲动力在较低转速既可达到最大动力输出
This depends on the revs in current gear, gear ratios and the rate at which the car can reduce speed.
这取决于当前档位的发动机转速,齿轮比和赛车减速的最大速率。
dead-slow speed servomotor
最小转速伺服电动机
maximum permissible speed of an abrasive whee
砂轮的最高容许转速
lowest continuous speed test with load
最低稳定工作转速试验
This potentially destructive rotational speed is called the" Critical Speed".
当旋转速度增大时,拱形会增大并最终导致丝杠遭到破坏。
This is to be completed in the time it takes the body to roll to, decelerate, and stop at the maximum rotation angle and then to accelerate and roll in the opposite direction.
这个动作在身体滚动的同时完成,减速,并在最大转动角度停止然后加速并转动到另一边。
Though admittedly starting from a smaller initial base, electronic information transfer has expanded much more rapidly in recent years.
电子信息转换的原有基础比较小,最近几年迅速扩大了领域。
engine turning at peak revolution
最大转数旋转的发动机
A float. Determines how long it takes for the motor to spin the vehicle to full speed. Its minimum value is approximately0.06 seconds.
一个浮量.觉得发动机使交通工具旋转到最大角速度的时间.最小值大约0.06秒.
"Best sample rate converter: provides best quality sample rate conversion but slowest performance.
"最佳示例速率转换程序: 提供质量最高的示例速率转换,但运行最慢。
Analysis of optimized wheel rotation speed of composite desiccant based on silica gel
硅胶基复合干燥剂转轮最优转速分析
The results showed that the influence of the lower impeller on NJSG was the largest, and three-bladed back-sweep impeller was the optimum.
结果表明,底层桨对临界搅拌转速的影响最大,最佳的底层桨为3叶后掠桨。
CopyRight © 2020-2024 优校网[www.youxiaow.com]版权所有 All Rights Reserved. ICP备案号:浙ICP备2024058711号