lower limit of variation是什么意思

网络释义

用法例句

Modifying dimension with limit deviation under AutoCAD condition,the limit deviation may be lost.

在AutoCAD环境下修改带有极限偏差的尺寸标注时,极限偏差可能会丢失。

Limit deviation is an important expression of technics and significant guarantee of manufacturing.

尺寸的极限偏差是工艺设计的表现结果和制造质量的重要保障 ,在实际生产过程中有着广泛的应用。

The selection of instrument, the processing of measured data, the determination of deviation limit, and the calculation of final uncertainty etc.

研究了燃煤锅炉热效率试验各测试项目中仪表的选择、测量数据的处理、偏差极限的确定、最终不确定度的计算等,给出了邢台电厂10号锅炉热效率试验、热效率计算和不确定度分析实例。

limit deviation of root circle diameter

齿根圆直径极限偏差

Limit deviations of angle without tolerance indication

GB/T11335-1989未注公差角度的极限偏差

Synchronous Limit Deviation of Press Brake under Eccentric Compression Circumstance

折弯机偏压情况下的同步极限偏差分析研究

Polypropylene (PP) pipes-Tolerances on outside diameters and wall thicknesses

GB/T13019-1991聚丙烯(PP)管材外径和壁厚极限偏差

Polyethylene (PE) pipes-Tolerances on outside diameters and wall thicknesses

GB/T13018-1991聚乙烯(pe)管材外径和壁厚极限偏差

Rational Design of Limit Deviation of Cone-thimble of Diving Pump for Well Application

井用潜水泵锥形套极限偏差的合理设计

Unplasticized polyvinyl chloride (PVC-U) pipes-Tolerances on outside diameters and wall thicknesses

GB/T13020-1991硬聚氯乙烯(PVC-U)管材—外径和壁厚极限偏差

Limits and fits--Bases--Part 3: Numerical values tables of standard tolerances and fundamental deviations

GB/T1800.3-1998极限与配合基础第3部分:标准公差和基本偏差数值表

" Limits and fits--Bases--Part 2: Basic rules of tolerances,deviations and fits"

GB/T1800.2-1998极限与配合基础第2部分:公差、偏差和配合的基本规定

Even in this limit, gases still show small deviations from the equation.

既使在这样的极限条件下，气体仍然对方程表现出小的偏差。

A Class of Strong Deviation Theorems for Partial Sums of Random Variables and Some Limit Theorems on Two Classes of Trees;

一类关于随机变量部分和的强偏差定理及两类树上的极限定理

Some Strong Deviation Theorems for Information Sources and a Class of Limit Theorems on an Extended Tree;

关于信源的若干强偏差定理及广义树上的一类极限定理

Some Limit Theorems of Linear Processes and Large Deviations for Empirical Measure Sequences;

线性过程的若干极限定理及经验测度的大偏差原理

MVUM (Minimum Variance Unbiased Estimator)

极小方差无偏估计器

Standard deviation, RSD and confidential limit should be reported.

均应报告标准偏差、相对标准偏差和可信限。

maximum percentage deviation of frequency weighted

加权频数极大偏差百分比

The Minimax Invariant Quadratie Unbiased Estimation of Variance Componet

方差分量的极小极大不变二次无偏估计

Discussion on Over-limit Offset of Steady Arm with Over-crossings under Limit Temperature in Shuozhou-Huanghuagang Railway Lines

朔黄线线岔极限温度下定位器偏移超限的探讨