polarizer/ phase shift layer是什么意思

网络释义

用法例句

Through analyzing the demand of thickness deviation, a new monitoring method basing on ultrasonic measurement technique and computer control technique was put forwared.

基于板厚偏差在线监测这一问题展开研究，采用智能仪器的设计方法和手段，进行人造板厚度在线监测系统的研究设计。

A new method for recording and reappearing colour image of an object is presented,Black and white plate is used for recoring and tricolour phase grating plate for reappearing,The method is very economical and conveninent.

介绍了一种用黑白底片记录，然后将记录得到的三色控制网屏与三色位相光栅板重叠以再现物体真实彩色像的新方法。

Based on the measured radiation pattern data of the antenna,a ralationship between phase offset and positional deviation of the phase center is founded by means of changing the reference point.

以天线相位方向图实测数据为基础,通过改变参考点,建立相位偏差与相位中心位置偏差的关系式,并利用最小二乘法估算天线相位中心偏差。

Influence of Bilateral Stiffness Difference of Wide Heavy Plate Mill on Thickness Deviation between Two Sides of Plate

宽厚板轧机两侧刚度差异对两侧板厚偏差的影响

Influence of Mill Bilateral Stiffness Difference on Hot Rolled Wide Heavy Plate Thickness Deviation

轧机两侧刚度差异对热轧宽厚板两侧厚度偏差的影响

Checking Rotor Runout And Thickness Variation

检查转子的偏摆和厚度的偏差。

edges of plates at joints

在连接处板边的偏差

The usual tolerance for steel plates of this thickness is1/8 inch.

这样厚的钢板通常公差是八分之一寸。

Effect of Central Segregation on Mechanical Properties of High Manganese Medium and Heavy Steel Plate

中心偏析对高锰钢中厚板力学性能的影响

Polypropylene (PP) pipes-Tolerances on outside diameters and wall thicknesses

GB/T13019-1991聚丙烯(PP)管材外径和壁厚极限偏差

Polyethylene (PE) pipes-Tolerances on outside diameters and wall thicknesses

GB/T13018-1991聚乙烯(pe)管材外径和壁厚极限偏差

Study on the Welding Technology and Microstructure of Unequal Thickness Laser Welding Tailored Blanks;

差厚激光拼焊板焊接工艺及其组织性能研究

Study on Forming of Differential Gauge Tailor-welded Blanks Based on Numeric Simulation;

基于数值模拟的差厚拼焊板成形工艺研究

The Study of the Frror Caused by Vibration in High-accuracy Laser Measurement Instrument for Thickness of Plate;

高精度激光板厚测量仪的振动误差研究

Experimental research on tensile test of B170P1 multi-gauge high strength steel laser tailor-welded blanks

B170P1差厚高强度钢激光拼焊板拉伸试验研究

Forming limit and weld seam movement of TWBs with different thicknesses in square cup

差厚拼焊板拉深方盒形件成形极限及焊缝移动

Research on Springback Rules and Control of U-shaped Bending of Tailor-welded Blanks

差厚拼焊板U形件的回弹规律及控制的研究

Round and square perforation plate screens-Thickness of below 3 mm

GB/T10612-1989板厚筛板

Wrought aluminium and aluminium alloy sheets and strips--Tolerances on form and dimensions

GB/T3194-1998铝及铝合金板、带材的尺寸允许偏差

A Panel Data Method of Correcting the Omitted Variable Bias in Regression Models;

回归模型中变量遗漏偏差补救的面板数据方法

Variation Modeling and Locating Optimization for Automotive Fender Assembly

轿车翼子板装配偏差建模与定位工艺优化