axial load是什么意思

网络释义

用法例句

By analyzing elastic distortion and contact form of deep groove ball bearing based on axial load is pressured between sleeve and ball,according to safe contact angle on condition that each component of bearing s relative displacement,the axial loaded capability for bearing can be estimated.

分析了深沟球轴承在轴向载荷作用下套圈与滚动体对压所产生的弹性变形及接触形态,以各元件相对位移时的安全接触角为依据,估算轴承的轴向负载能力,从而对选择轴承的型号提供参考[1]。

Bearings shall be specifically selected to carry all radial and axial loads imposed by the pump and motor.

这些轴承都是经过特别挑选,能够承担由泵和电机产生的径向和轴向负载。

Full enclosure to allow gasket to retain positive radial support during loading.

在负载期间，全封闭外科使得垫圈能够保持正轴向支撑。

Metal - Axial load fatigue testing???

金属－－轴向负荷疲劳试验

Most Bearings support rotating shafts against either transverse (radial) or thrust (axial) loads.

大多数轴承都支承径向或轴向负荷的转轴。

The weight of the load swayed the boat to the left.

负载使船侧向左边。

General specification for coaxial line electrical dummy loads

GB/T12774-1991同轴电气假负载总规范

Deep groove ball bearings mainly take radial load as well as take moderate axial load.

深沟球轴承主要承受径向载荷，也可承受一定量的轴向载荷。

Axial load-deformation curve and preload on angular con act ball bearings

角接触球轴承的轴向载荷—变形曲线和预紧

The Research on Equal-strength Design of Large-scale Heavy-load Cross-shaft Universal Clutch

大型重载十字轴式万向联轴器等强度设计研究

This paper describes the design method of broad band coaxial termination load.

本文叙述了宽带同轴终端负载的设计方法.

Study of Simulate and Control of Single Axis Electric Platform with Great Load;

大负载单轴电动转台的仿真与控制研究

Design for Realtime Tracking-Control System of Two-Shaft Turntable;

变负载两轴转台实时跟踪控制系统的设计

Bearing selection shall limit the bearing temperature rise to a maximum of 60 C under full load operation.

在全负载状态下,所挑选的轴承将轴承温度限制在60℃以下。

Design and Optimization of Double-Axes Turning Machenism on Heavy Vehicles;

重载汽车双轴转向系统的设计与优化

Numerical investigation on interaction of axial and lateral response for super-long pile

轴-横向荷载作用下超长桩数值模拟

The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing.

为了避免划伤，轴承上的最大负荷应该总是小于其卸载负荷。

The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing and brineling.

为了避免划伤和压坑，轴承上的最大负荷应该总是小于其卸载负荷。

Four pionts angle contact ball bearing is separable bearing,it can be subject to bi-directional load and have the function of both single row and double rows bearings.

四点接触球轴承为可分离型轴承，可承受双向轴向载荷，并有单列和双列角接触球轴承的功能。