conical boring是什么意思

网络释义

用法例句

This paper introduced the mechanism of vibration in the process of deep hole boring,developed a dynamic modal of the damping boring bar,optimizing the parameters of the damping system,analyzed the transient dynamic and harmonic response of the damping boring bar.

介绍了深孔镗削加工过程中产生振颤的机理,建立了减振镗杆的动力学模型,在此基础上优化减振系统的参数,并且对减振镗杆进行瞬态动力学和谐响应分析,分析结果表明该减振系统具有良好的减振性能。

Based the characteristic of deep hole boring chatter,a dynamic model of magnetorheological(MR) intelligent boring was established by means of equivalent linearization technique.

针对深孔镗削过程中的颤振问题,提出了一种基于磁流变液的智能镗杆构件,并根据深孔镗削颤振的特点建立了磁流变智能镗杆切削系统的动力学模型。

On the base of studying the forming mechanism of spire ditches in deep-hole boring process, this paper analyses theoretically the effect of the boring bar diameter on the oscillation and spire ditches and established the mechanical model.

在研究深孔镗削螺旋沟产生机理的基础上,对深孔镗削加工过程中镗杆直径对振动及螺旋沟的影响进行了理论分析及力学建模,并通过试验研究了增大镗杆直径对减小振动和抑制螺旋沟的积极作用。

The frequency response for deep-hole boring process is analyzed by the method of graph.

通过拉普拉斯变换后得到临界稳定下的系统特征方程,利用图解法作出深孔镗削加工振动的频率响应轨迹曲线,对深孔镗削时自激振动产生的机理和稳定条件进行了系统的理论分析和研究,指出了镗削加工过程中绝对稳定边界及稳定下的阻尼比取值范围;结合实验结论和长期积累的实践经验,给出了车床深孔镗削加工中切实可行的减振和防振措施,为机械加工技师和工程技术人员的实际工作提供了参考。

Suppression of chatter for precision hole boring based on variable structural stiffness

基于变结构刚度抑制精密孔镗削加工的颤振

INVESTIGATION OF THE RELATIONSHIP BETWEEN CHIP FORM AND CUTTING CONDITION AS WELL AS MACHINING QUALITY IN DEEP HOLE BORING

深孔镗削中切屑形态与加工条件及加工质量的关系探讨

The Application of Boring Bar Pared Flat and the Technology of Damping Absorption in the Manufacture of Deep Holes

削扁镗杆与阻尼减振在深孔加工中的应用

Boring operations are performed to enlarge, finish, and accurately locate holes.

镗削用来扩大、精加工和加工精确定位孔。

Suppression of chatter for precision hole boring based on variable structural stiffness

基于变结构刚度抑制精密孔镗削加工的颤振

Technology Method of High Speed Boring on Module’s Positioning Hole

高速镗削扩径头模块定位销孔的工艺实现

Analysis on Design of Three-position-cylinder when Changing Gear of Deep Boring CNC Mill

数控深孔镗床三位换档油缸的换档设计分析

Dynamic Simulation and Parametric Analysis of Dynamical Vibration Absorption Boring Bar for Deep-Hole Processing;

深孔加工动力减振镗杆的动力学仿真与参数化分析

The investigation on chip deformation and cutting forces of BTA deep hole drilling

内排屑深孔钻削切屑变形与切削力实验研究

two-side horizontal boring transfer machine

双面卧式镗孔组合机床

bore face machine

镗孔锪端面加工机床

finish boring machine for five holes on final drive house

主减速器壳五孔精镗

rough boring machine for five hole on final drive house

主减速器壳五孔粗镗

high efficiency drilling system for small and deep hole

高效小直径深孔钻削系统

Experimental research on the system performance in near-dry deep hole drilling

亚干式深孔钻削系统性能的试验研究

The Academic Optimization of Cutting Parameter of Machining Small-deep Hole

小直径深孔加工切削用量的实验优选

An experimental study of drilling small and deep blind holes with an abrasive water jet

磨料水射流钻削深小盲孔的试验研究

Terminology for metal-cutting machine tools--Boring machines

GB/T6477.5-1986金属切削机床术语镗床

Research on Method to Get Amount of Feed for the Non-Circular Boring System;

异形镗削系统进给信息获取方法研究