Yield strangth是什么意思

网络释义

用法例句

Effect of phosphorus on the yield strength of as-quenched GH761 alloy;

磷对GH761合金固溶水淬组织屈服强度的影响

Study of influence factors of yield strength of oil and gas pipeline;

油气管道屈服强度影响因素的研究

A modeling study of the yield strength of HRB335 hot rolled ribbed bar;

HRB335热轧带肋钢筋屈服强度模型研究

Based on the plain carbon steel with the chemical composition of 200MPa class steel the products of the yield stress of 400～500 MPa class and high-quality mechanical properties can be produced using the technology of chemistry tightly-tuning and controlled rolling - controlled cooling.

以屈服强度为 2 0 0MPa级的普碳钢为基本成分 ,采用成分微调与控轧控冷工艺相结合的技术路线 ,可将屈服强度提高到 4 0 0～ 5 0 0MPa,同时保证良好的综合性能。

From the tests, a two-stage linear relation has been found between yield stress(σ_s) and strain rate(ε),σ_s=σ_0+klgε.

对４种金属材料进行了应变率为１０~（－４）—１０~３ｓ~（－１）的拉伸试验，结果表明，屈服强度随应变率的升高分两阶段线性升高。

Yielding behavior of mismatched welded joint and prediction of its yielding strength;

非等强焊接接头屈服行为及屈服强度预测

Mechanical properties of normalized and tempered 12Cr2Mo steel forgings,primarily yielding strength,were on the low side.

汽轮机用12Cr2Mo钢锻件经正火、回火后,其力学性能(主要是屈服强度)偏低,一次热处理后的合格率仅为50%,既造成该钢锻件大量热处理返修,又严重影响了生产周期。

"Yield strength 85Kg/mm2(120,000psi)maximum"

屈服强度最大85Kg/mm2(120000psi)

"Maximum shear Strength 63Kg/mm2(90,000psi) maximum (based on 75% yield) "

剪切强度最大63Kg/mm2(90000psi)(为屈服强度的75%)

Study on Increasing Yield Strength of Q345B Plate in JISCO;

提高酒钢Q345B板材屈服强度研究

Research on dynamic yield strength of steel 30CrMnSiNi2A

30CrMnSiNi2A钢的动态屈服强度研究

Analysis of Cracking During Stamping of 700MPa Grade Super High Strength Beam Steel

屈服强度700MPa级超高强度大梁钢冲压开裂分析

Influence of strength of ferrite matrix on yield strength of granular structure steels

铁素体基体强度对粒状组织钢屈服强度的影响

Experimental research and prediction of yield strength for aging strengthened aluminium alloy

铝合金时效强化的实验研究及屈服强度计算

Effect of Heat Treatment System and Test Method on Yield Strength of LY12MCZ Alloy

热处理制度和试验方法对LY12MCZ屈服强度的影响

Yielding strength is indicative of the stress at which plastic deformation begins.

屈服强度是指塑性形变开始发生时的应力。

EXPERIMENT AND MODELING STUDY OF AGED ALU-MINIUM ALLOYS STRENGTHENING RESPONSE

铝合金时效-屈服强度的实验与模型化研究

Effects of Heat-treatment Technology on the Yield-Strength of A356 Wheel by Low-Pressure Casting;

热处理工艺对A356低压铸造轮毂屈服强度的影响

The Influence of Steel Bar Yield Strength Error to Structure Design;

钢筋屈服强度的误差对结构设计的影响

Effect Factors Analysis on Measuring X80 Grade Pipeline Steel Yield Strength

X80级管线钢管屈服强度测量影响因素的分析

Effects of Nb Content on Yield Strength of NiTiNb Alloys in Martensite State

Nb含量对NiTiNb合金马氏体态屈服强度的影响(英文)

Analysis of Unqualified Strength of 20MnSiV Hot Rolled Ribbed Bars

20MnSiV热轧带肋钢筋屈服强度不合原因分析

Effect of residual stress on yield strength of air-cooled bainitic steel

空冷贝氏体钢的残余应力对屈服强度的影响

STRESS-STRAIN BEHAVIORS AROUND THE YIELD STRENGTH IN SEQUENTIAL ROOM TEMPERATURE CREEP TESTS

相续室温蠕变中屈服强度附近的应力应变行为

Properties of Low Yield Point Steels Used for Earthquake Resistant Buildings

建筑抗震阻尼器用低屈服强度钢的性能