draw是什么意思

网络释义

用法例句

Based on the encapsulate curve of structural unit for the molded paper pulp,rela-tionship of the taper angle of structural unit was revealed for the molded paper-pulp and cushion perform-ance,and it was found that the best taper angle of structural unit is 4°~8°.

利用有限元分析软件,针对纸浆模塑典型结构单元,应用双线性运动增强型材料模型,进行系统力学分析,以力学分析得到的纸浆模塑缓冲结构单元的静态压缩曲线为基础,得出了缓冲包装结构拔模斜度对缓冲性能存在较大的影响,斜度在4°~8°时缓冲性能最佳的结论。

The studies showed that the reverse draft was caused by the effect of die locking force reiteratively in the long die casting processes.

研究表明,模具中反拔模斜度的形成,是由于合型力长期作用的结果。

In this paper,the impact of draft angle to the moulding dimensions and the comprehension of the dimensions in plastic production with the unlabeled tolerance were discussed.

本文通过论述模具脱模斜度对模具尺寸的影响、塑料件未注公差的确定,并通过一个设计实例进行了说明。

Machine molding will require a minimum amount of draft.

机器造型需要的拔模斜度最小

Interior surfaces in green sand molds usually require more draft than exterior surfaces.

砂模的内表面经外表面需要更大的拔模斜度

The studies showed that the reverse draft was caused by the effect of die locking force reiteratively in the long die casting processes.

研究表明,模具中反拔模斜度的形成,是由于合型力长期作用的结果。

Draft allowances can be incorporated into dimensional tolerances or geometric tolerances only upon consultation with the foundry.

拔模斜度余量只有经与铸造厂商定后才能合并到尺寸公差或形位公差中。

draft is required on the vertical surfaces to allow the pattern to be drawn away from the mold.

在垂直面需要起模斜度以便模样从铸型中拔出。

Any of various surveying instruments for measuring angles of elevation, slope, or incline, as of an embankment.

测斜器，倾角计一种测量海拔、斜坡或倾斜的角度的测量仪器，如测路基倾斜度用

Effects of second premolar extractions on third molar angulations

正畸拔除第二前磨牙后第三磨牙倾斜度的变化

Calculating the Taking out Force in the Plastic Injection Mould;

塑料注射模斜导柱抽芯机构中抽拔力的计算

Simulation on Structural Reliability of Cable-Stayed Aerial Crossing Pipeline Structure;

斜拉索管道跨越结构可靠度随机模拟

Time-domain Vibration Analysis of Long-span Cable-stayed Bridges Model Structure;

大跨度斜拉桥模型结构动力时程分析

The Best Calculation of Technological Gradient for Plastic Mould Cavity by Cold-Pressing;

塑料模冷挤型腔最佳工艺斜度的计算

Cable Force Simulation for Super Long-Span Cable-Stayed Bridges Based on ANSYS

基于ANSYS的超大跨度斜拉桥的索力模拟

The Solution of Surface Integral for the Velocity Field of Square Bar Drawing Through a Cosine Die

余弦模拉拔方棒速度场的曲面积分解法

Measurement and Study of Dental Model after Nonextraction Treatment in Adult Patients with Mild Crowding;

成人轻度拥挤非拔牙矫治前后的模型测量研究

The1.4-kilometre line began operation in 1888 and was modernised in 1989.

缆车线全长1.4公里，从中环直达海拔373米的山顶，途经的地点，有些斜度达1:2。

The degree of such a slope.

斜度这种斜坡的度数

Figure 2.1 illustrates the use of draft on a typical pattern and corebox.

图2.1 说明了起模斜度在一个典型的模样和芯盒

Temperature Field and Yield Stress Grads during Wire Die-Less Drawing of Tungsten Alloy

钨合金丝材无模拉拔成形温度场及流动应力梯度