cooling time是什么意思

网络释义

用法例句

Analysis of Affecting Factor on Cooling Time of Injection Molding;

影响注射成型冷却时间的因素分析

Cooling Time Oetermination of injection Molded Parts;

注塑制品冷却时间的确定

Influence of cooling time on the bond strength of VITA TITANKERAMIK to the cast titanium;

冷却时间对VITA TITANKERAMIC与钛铸件结合强度的影响

According to the half-cooling time,contents of every alloy element were determined by adopting the broad sense Dodd-formula for calculating hardenability of the High-Cr white cast iron.

根据铸件的半冷却时间,用广义Dodd计算高铬铸铁的淬透性公式,求出各合金元素含量。

Establishment of critical cooling time criterion t_(cr) of welding cold cracking;

焊接冷裂纹临界冷却时间判据t_（cr）的建立

On the basis of the result of the Y-slit crack test,the critical preheat temperature and critical cooling time(t_(8/5cr)) of JG590 under the condition of different heat input and welding material were determined by theoretic computation.

采用插销实验、斜y形坡口焊接裂纹实验和焊接热影响区最高硬度实验对厚度30 mm的JG590钢板的焊接冷裂纹敏感性进行了研究,分析了插销试件的断口和显微组织,以斜y形坡口焊接裂纹实验结果为基础,通过理论计算得到了JG590钢在不同焊接线能量、不同焊接材料情况下的临界预热温度和临界冷却时间。

On the basis of the above research, the critical cooling time criterion tcr of domestic HSLA steels is establishe.

建立了国产低合金高强钢的临界冷却时间判据ｔｃｒ。

By decreasing the grade of cast iron,using furan resin selfsetting sand as a substitute for clay sand to make the core and prolonging cooling time in mould,the cracking problem has been solved.

通过降低材料牌号,使用呋喃树脂自硬砂取代粘土制芯,延长铸件在型内冷却时间,使裂纹缺陷问题得到解决。

cooling the preform mould by chiller instead of water tower could reduce the cycle time by 10%.

以冰水冷却瓶坯模具比水塔水冷却缩短冷却时间10%

Preparation now resets the cooldown of Shadowstep and no longer resets the cooldown of Adrenaline Rush.

预备：现在它重置“暗影步”的冷却时间，但不重置“冲动”的冷却时间了。

Lightning Shield" will now have the appropriate cool-down time between uses.

闪电盾现在有了正确的冷却时间。

Counterspell" no longer triggers the global cooldown.

法术反制”不再触发全局冷却时间。

This talent no longer reduces the cooldown of Sprint.

这个天赋不再减少急跑得冷却时间。

Can be directed using Target of Vengeance.

施法距离700，冷却时间35秒。

Cooling time dominates cycle time in thick-wall moulding like preform moulding.

属厚壁注塑的瓶坯，冷却时间支配着周期时间。

When chilled water is used to cool the mould, cycle time is related to wall thickness as follows.

在冰水冷却的条件下，冷却时间与壁厚有以下的关系。

Allied Supply Drop cooldown increased to5 m from3 m.

空投资源冷却时间从3分钟增加到5分钟。

Increase in cooling time is proportional to the square of the increase in thickness.

冷却时间增加同厚度增加的平方成正比。

Crusader Strike (Retribution) cooldown reduced from 10 to 6 seconds.

十字军打击冷却时间从10秒减少到6秒。

The Kelvin cooling time for the Earth is then about 30,000 years.

在开尔文的冷却时间，地球是那么大约3.0万年。

Welding parameter.( Reference values for electric socket welding-welding time and cooling time.

熔接参数(考数值为电承插热熔，热熔时间和冷却时间.

From all testing so far, this cooldown appears to be10 minutes for Uncommon gems and60 minutes for Rare gems.

从目前测试来看，对于绿色宝石冷却时间10分钟，蓝色宝石冷却长达1小时。

Warlock: Death Coil has no cooldown against Rogues, and has a range of100 yards.

术士:死亡缠绕在对盗贼的时侯将没有冷却时间,范围扩大到100码.

indirect cooling air cooler

间接冷却式空气冷却器

Analysis of Influence of Decay-Cooling Time on on-Line Burnup Measurement of HTR-PM

冷却衰变时间对球床模块式高温气冷堆在线燃耗测量的影响分析

horizontal intercooled ammonia converter

卧式中间冷却氨合成塔