run是什么意思

网络释义

用法例句

Miniaturization of the channel size makes the flow behaviours of polymeric melt different from the macroscopic fluid at some aspects,and the neglected factors in macroscale for melt flowing may become the main influencing factors in microscale.

基于宏观熔体流动的基本理论及其流动过程中壁面滑移机理的分析,针对微注塑成型模具中熔体充模流动时的壁面滑移行为,建立了微小通道中高聚物熔体流动的壁面滑移理论模型。

e model of the melt flow in the metering zone of the single screw extruder under the vibration force field was set up and the approximate analytical solution of the velocity of the Newtonian fluid was obtained.

建立了振动力场作用下单螺杆挤出机计量段中熔体流动的物理模型,在Stokes假设基础上,得到了螺槽内牛顿流体速度分布的解析解。

Semi-solid ZL101 alloy with granular microstructures has been successfully produced by controlled crystallization, and the effect of melt flow at initial solidification on granular primary phase formation is analyzed.

采用控制熔体结晶法制得颗粒状组织半固态 ＺＬ１０１合金，研究了结晶初期熔体流动对粒状初晶形成的作用。

testing method for melt flow rate of thermoplastics

热塑性塑料熔体流动速率试验方法

THE FLOW ANALYSIS OF POLYMER MELT IN CO-EXTRUSION DIE

共挤出机头中的聚合物熔体流动分析

PIV Analysis on Flow in the Mold during Continuous Casting of Steel Slab;

板坯连铸结晶器内熔体流动的PIV分析

Analysis for three-dimensional flow field ofplastics melt in fishtail die

鱼尾型机头中熔体流动的三维流场分析

Numerical Analysis of Flowing for High Polymer in Spinning Pack and Optimization the Structural of It;

熔融纺丝组件熔体流动数值分析及其结构设计优化研究

Study on the mechanical properties and melt flow rate of SBS/ESBS blends

SBS/ESBS共混体系力学性能及熔体流动速率的研究

Test method for melt flow rate of thermoplastics

GB/T3682-1983热塑性塑料熔体流动速率试验方法

The Simulation and Analysis of the Flow in Lattice Extrusion Tube Die

篮网式管机头中熔体流动的模拟及分析

COMPUTER SIMULATION OF FLOWING STATE OF PLASTICS MELT IN SLIT DIE SECTION

计算机模拟狭缝口模截面塑料熔体流动行为

THREE-DIMENSIONAL FINITE ELEMENT SIMULATION OF FLOW OF MOLTEN POLYMER IN FISHTAIL DIE

鱼尾型片材机头内熔体流动的三维有限元模拟

Computer Simulation of Melt Flow in Pipe Die with Spiral Mandrel

螺旋式管材机头内熔体流动的计算机模拟

Numerical Simulation on Melt Flow Characteristic of Flat Spiral Type Die for Blown Film

平面螺旋式吹膜模头熔体流动特性的数值模拟

The test level evaluation of the melt mass-flow rate of synthetic resin of petrochina

中国石油合成树脂熔体流动速率测试水平评价

Numerical Si mulation of Melt Flow Characteristics in Spiral Mandrel Die for Blown Fil m

螺旋芯棒式吹膜模头熔体流动特性的数值模拟

Study on Modelling of Fluid Flow in Iron-bath Smelting Reduction Furnace with Multi-phase Model

多相流模型模拟熔融还原炉内流体流动

Experimental Study on Fluid Flow Characteristics in the Smelting Reduction Furnace by Water Model

熔融还原炉流体流动特性的物理模拟研究

Simulation of Fluid Dynamics Behavior and Solidified Structure in Welding Pool;

焊接熔池的流体动力学行为及凝固组织模拟

CAE Optimization of Melt Filling about Large-sized and Exact Injection Mold;

大型精密注塑模具熔体充模流动CAE优化分析