Direct quenching是什么意思

网络释义

用法例句

Selection of a Corrosive for Direct Quenching Method to Determine Grain Size;

直接淬火硬化钢晶粒度腐蚀剂的选用

Study of direct quenching process for SPV490 steel plate;

SPV490钢板直接淬火回火工艺的研究

Effect of Rolling-Direct Quenching Parameters on Structure and Properties of Ti-B Microalloying Low Carbon Si-Mn Steel

轧制-直接淬火参数对Ti-B微合金化低碳Si-Mn钢组织和性能的影响

Study on Microstructure and Mechanical Properties of Direct-Quenched Medium Carbon Steel;

直接淬火中碳钢的微观组织与力学性能研究

Direct Quenching Technical Study of Ti-B Microalloying Low Carbon Si-Mn Steel

Ti-B微合金化低碳Si-Mn钢直接淬火工艺研究

800MPa grade heavy plates with low susceptibility to welding crack produced by direct quenching

直接淬火研制800MPa级低焊接裂纹敏感性高强钢厚板

The heat treatment technology of carbo- nitriding of steel has the characteristic of lower treatment temperature and direct quenching.

钢的碳氮共渗热处理工艺具有共渗温度低、直接淬火等特点。

Effect of Rolling-Direct Quenching Parameters on Structure and Properties of Ti-B Microalloying Low Carbon Si-Mn Steel

轧制-直接淬火参数对Ti-B微合金化低碳Si-Mn钢组织和性能的影响

tension electric process

电流直接加热淬火法

Effect of Tempering Temperature on Structure and Mechanical Properties of Steel 15CrMoV Direct-Water-Quenched after Finishing Rolling

回火温度对轧后直接水淬15CrMoV钢组织和力学性能的影响

Quenchant Non-contact Hardening Technology Experimental Research of Circular Saw Blade

圆锯片淬火介质非接触式淬火技术的实验研究

Influence of overlapping amount on hardness of 9Cr2 steel by laser hardening

搭接量对激光淬火9Cr2钢硬度的影响

Under high stress or low stress abrasion working conditions, high Cr white cast iron can be used just after it having been air quenched.

高应力磨料磨损或低应力磨料磨损工况条件下,高铬白口铸铁空淬后不须回火可直接应用。

Tempering softening of overlapping zones during multi-track laser quenching for carbon steel and alloy steel

碳钢及合金钢搭接激光淬火回火软化特征

Magnetic Field Shielding in End-to-end Zone of Brachy-axis-like Parts during Continuous Induction Quenching

连续感应淬火的短轴类零件首尾连接处的屏蔽

The paper describes quenching technique about this flange and its character.

介绍了满足半轴法兰圆角大直径范围淬火感应器的设计、应淬火工艺参数以及半轴的性能。

continuous quench and temper line

淬火回火连续作业线

Doppelduro method

乙炔火焰表面淬火法

Why shall harden steel be annealed ?

淬火钢为什么要退火呢?

Tight scale is usually a problem encountered in forgings hardened from direct-fired gas furnaces having high-pressure burners.

用高压炉头直燃煤气炉对锻件进行淬火时，通常会出现鳞片问题。

As for small diameter workpiece, martensite distribution can be obtained by immediately quenching.

对于直径较细的工件，轧后立即淬火几乎可得到全部马氏体。