alternate bending strength是什么意思

网络释义

用法例句

Studies on the Relations of Gear Bending Strength and the Undercutting Thickness;

齿轮弯曲强度与沉切量关系研究

Influence of process on the bending strength of SiC_f/Si-O-C composite;

制备工艺对SiC_f/Si-O-C复合材料弯曲强度的影响

Dynamic elastic modulus-bending strength of cured LPA/UP with acoustical resonance;

声频振动法测定LPA/UP固化物动弹模量-弯曲强度的试验研究

Influence of γ-ray irradiation APMOC fiber on flexural strength of AFRC;

γ-射线辐照APMOC纤维对AFRC弯曲强度的影响

Statistical significance of flexural strength of IPS-Empress2 glass-ceramics;

IPS-Empress2玻璃陶瓷弯曲强度的测试及意义

The influence of marking technology on the flexural strength of denture bases;

刻痕标记技术对义齿基托塑料弯曲强度的影响

The recently-developed PdCo-(4~20)V-4Ni-Si-B brazing foils were used for SiC joining,and the room-temperature three-point bend strengths of the SiC/SiC joints brazed at 1463 K and 1493 K for 10 min are 52.

设计的PdCo-(4~20)V-(2~4)Ni-Si-B钎料可用于SiC的连接,在1463 K,1493 K两个温度,保温时间均为10 min的连接条件下得到的接头室温三点弯曲强度分别为52。

The mechanical models of bend stiffness and bend strength of the pallets girder and deck were established.

通过分析木托盘在均布载荷作用下的受力变形情况,建立了木托盘梁和铺板的弯曲强度和弯曲刚度的力学模型,提出了托盘弯曲强度和刚度的条件。

The fracture toughness and flexure strength from room temperature to 900℃ of zirconium diboride-silicon carbide(ZS) composites and zirconium diboride-silicon carbide with the addition of short carbon fiber(ZSC) were examined and analyzed.

对ZrB2-SiC(ZS)材料和碳短纤维/ZrB2-SiC(ZSC)材料的断裂韧性、室温至900℃弯曲强度进行了测试和研究。

The volume density,open porosities and flexure strength of porous silicon nitride ceramics are measured respectively by Archimedes and three-point bend.

利用阿基米德法、三点弯曲法测试了材料的密度、显气孔率及弯曲强度;借助扫描电子显微镜(SEM)进行微观结构分析。

The effects of temperature on the notch flexure strength of alumina are experimentally investigated.

试验研究了温度对Al2 O3 陶瓷弯曲切口强度的影响 ,结果表明 :在 2 0～ 80 0℃之间 ,材料的弯曲强度和弯曲切口强度不仅没有降低 ,甚至略有升高 ,它们的分散性随着温度的升高而降低 ,但在 95 0℃条件下 ,其弯曲强度和弯曲切口强度均显著降低 。

Test method for cross-bending strength of porous ceramic

GB/T1965-1996多孔陶瓷弯曲强度试验方法

Testing method for flexural strength of high performance ceramics

GB/T6569-1986工程陶瓷弯曲强度试验方法

Test method for flexural strength of ceramic tiles

GB/T8917-1988陶瓷砖弯曲强度试验方法

Test method for cross-bending strength of vitrified pipe

GB/T2833-1996陶管弯曲强度试验方法

testing method for flexural strength (modulus of rupture) of high performance ceramics

工程陶瓷弯曲强度试验方法

EXPERIMENTAL STUDY ON THE FLEXURAL STRENGTH OF FINE GRAIN ETHANOL MODEL ICE

细粒酒精模型冰的弯曲强度试验研究

Weibull Statistical Analysis of Bending Strength of Quartz Ceramic

石英陶瓷弯曲强度的Weibull统计分析

Finite element analysis of gear flexural strength under UG background

UG环境下齿轮弯曲强度的有限元仿真

Effect of Grinding Induced Damage on Bending Strength of RBSiC

磨削表面损伤对RBSiC弯曲强度的影响

fine ceramics(advanced ceramics, advanced technical ceramics)-test method for flexural strength of monolithic ceramics at elevated temperature

细陶瓷-单块陶瓷高温弯曲强度试验方法

Test method for flexural strength of high performance ceramics at elevated temperature

GB/T14390-1993工程陶瓷高温弯曲强度试验方法

Testing method for static flexural strength of piezoelectric ceramics

GB/T11387-1989压电陶瓷材料静态弯曲强度试验方法

Study on the Bending Strength and Contact Stress of Large Module Involute Cylindrical Spur Gear;

大模数直齿轮轮齿弯曲强度与齿面接触研究

Study on the Bending Strength of Large Module Involute Cylindrical Spur Gear;

大模数渐开线直齿圆柱齿轮弯曲强度研究

Study on the Bending Strength of Case-hardened Double-circular-arc Gear;

硬齿面双圆弧齿轮齿根的弯曲强度研究

The Influence of Design of Hob Cutter Tip on Teeth Bending Strength;

滚刀刀顶设计及对齿根弯曲强度的影响

repeated bending stress strength

反复弯曲疲劳强度极限

Influence of Training with Secondary Load on Bending Fatigue Strength of Cranksh aft

次载锻炼对曲轴弯曲疲劳强度的影响