case housing是什么意思

网络释义

用法例句

Technological analysis and design of flanging die for fuel oil tank shell

油箱壳体成形工艺分析与翻边模设计

Defects like local deformation in an ice box inner casing during foaming process may occur due to decrease of plate thickness;and the main factors were found to be the accurate degree of fitting between the foam mould and the box inner casing.

针对板材厚度降低导致发泡过程中箱体内壳局部变形等质量缺陷,发泡模与箱体内壳的配合准确程度是主要因素。

Introduced the characteristics of the gear box case, and determinded the reasonable forming process, designed the drawing die, the trimming die, the piercing die and the flanging die.

介绍了变速箱壳体零件的工艺特点,确定了合理的工艺方案,设计了拉伸模、切边模、冲孔模、翻孔模,经生产验证,模具结构合理,生产的零件完全满足要求。

Simulation Analysis and Experimental Validation of Thin Gear-box Shell Dynamic Responses

薄壳变速箱壳体动态响应仿真分析与试验验证

Finishing Technology of Large Diameter Blind Holes in Hydraulic Oil Tank Case

液压油箱壳体大盲孔的光整加工技术

Processing Quality Forecast and Diagnosis for Gear-box Shell Production Line

变速箱壳体机械加工质量预测与诊断

Technological analysis and design of flanging die for fuel oil tank shell

油箱壳体成形工艺分析与翻边模设计

Quality-control and Production of the Die Casting Cylinder-Block and Transmission Case

发动机缸体与变速箱壳体压铸生产及质量控制

Developing of Rear Bridge Transmission Case Sieries

北汽福田后桥变速箱壳体系列产品开发

The Experiment Research on the Electromagnetically Assisted Sheet Forming of Aluminum Fuel Tanks Shell;

铝合金油箱壳体电磁成形复合冲压试验研究

Multistage Manufacturing Quality Control and Diagnosis Based on Gearbox Casing

变速箱壳体多工序机加工的质量控制与诊断

Forming Process Analysis and Die Design for the Automobile Gear Box

汽车变速箱壳体成形工艺分析及模具设计

Gearbox is the key components in the automobile, and the casing is key part in the gearbox.

汽车变速器是汽车的关健部件，而变速箱壳体又是变速箱中的关键零件。

To provide a housing or case for(a machine part, for example).

装箱为（机体，例如）提供套壳或箱子

"To provide a housing or case for (a machine part, for example)."

为(机体,例如)提供套壳或箱子。

SUN HYDRAULIK GMBH offers Offers to Screw-in valves, Globe valves and Valve housing.

提供轴承箱、轴承体、阀体、阀箱、阀套、阀门外壳及其它产品。

Design and Calculation Strength of Flame proof Rectangular Tank for Mine

矿用隔爆型矩形箱体外壳强度设计计算

Free vibration analysis of box-girder bridges using incompatible degenerated solid shell element

箱梁桥自振分析的非协调实体退化壳元法

The Technological Process Analysis of Stamping Forming for the Outside Shell of Fuel Tank of Ride-Motorcycle

骑式摩托车油箱外壳体冲压成形工艺过程分析

For boot top, hull interior and exterior, or container exterior.

主要用于船体的水线，船壳内、壁使用、可用于集装箱外壁使用。

Non-pollution,The pump body is made of polyvinyl chloride (pvc)plastics,and the onter cover is of cold-rolled steel plate with backing finish.

无污染，本机箱体为聚氯乙稀塑料，外壳采用不锈钢和冷板静电喷塑壳两种。