depressed position是什么意思

网络释义

用法例句

2 Steelmaking Plant of WlSCO,the main technological parameters were analyzed and optimized, such as reduction position,reduction amount,and reduction ratio.

结合武钢二炼钢动态轻压下技术的应用情况,对压下位置、压下量、压下率等主要参数进行了分析及优化。

COMSOL software is used to simulate the solidification process of the square billet continuous casting,and factors which influence the position of the solidification point have been analyzed,which provides a effective means for determining the dynamic light screw down position of the casting blank.

本文采用COMSOL软件模拟方坯连铸的凝固过程,分析了影响凝固点位置的因素,为确定铸坯的动态轻压下位置提供了一种有效的手段。

A robust dynamic output feedback synchronous controller is designed for the pressing down position system with uncertain parameters and outside load disturbance.

冷带轧机操作侧和传动侧位置子系统的内部参数和外界负载不一致,并且均存在一定的不确定性,这会造成两侧压下位置系统动静态性能不同和压下位置的不同步,从而影响被轧带材两侧的厚度和板形质量。

Optimization Study on the Pressure Position of Dynamic Soft Reduction for Continuously Cast High-level Pipeline Steel

高级别管线钢板坯动态轻压下最佳压下位置研究

Study on Heat-transfer Model of Solidification and Prediction Model of Soft-reduction Position for Continuous Casting Slab;

板坯连铸凝固传热及压下位置预报模型的研究

Robust Dynamic Output Feedback Synchronous Control for Both Sides of Pressing Down Position System for Cold Rolling Mill

冷带轧机两侧压下位置系统鲁棒动态输出反馈同步控制

Note: Use a pressure gauge downstream to adjust and verify the pressure setting.

注：在下游位置采用压力表进行调节并核对压力设置结果。

Illustrated below are some commonly accepted positions of the lever and weight.

下图是常见的、能够接受的操纵杆和压铁位置。

Study on the arc tracking system of all-position pulsed TIG welding under high-pressure environment

高压环境下全位置脉冲TIG焊弧长跟踪系统研究

hydraulic roll screwdown

液压式轧辊压下装置

"If air compressor is reciprocating type, Check Valves shall be downstream of receiver tank."

如果空气压缩机是往复型,则止回阀应该位于接受槽的下游位置。

(3) the dynamic pressure of tidal bore reaches maximum little below the original tidal level, and decreases with the increase of depth.

(3)涌潮动压力在低潮位偏下的位置达到最大值 ,然后逐渐减小。

To place in a prone position.

使倒伏置于向下的位置

centre position

中间位置，(液压泵的)正常位置

CONNECT AN OIL PRESSURE GAUGE IN ITS PLACE.

在这个位置连接油压计。

a secondary or inferior position or status.

第二位的或低下的位置。

Computer control of hydraulic screw down system should have a function of rolling force closed circuit control and roll position closed circuit control.

电气控制系统中的液压压下计算机控制系统要实现轧制压力闭环控制和轧辊位置闭环控制

Wide profile processing range due to convenient locating and clamping device setting.

压紧与定位装置上、下、调，可适用于各种规格、面的型材，通用性强。

"After the engine starts and the ignition key is released, spring pressure returns it to the ON position."

发动机启动以后,点火钥匙回转,在弹簧的压力下,恢复到"开启"位置。

Further tweak to make more early shots when under pressure or in good position.

在压力下和处于好位置时，球员会选择更早地射门。

Design of Hydraulic Pressure Transmission System of the Repairing Checking Clamp of Plane

某型飞机主起落架放下位置锁检测夹具用液压传动系统的设计