Discussed on the installation position of several hydraulic elements;
对几种常见液压元件安装位置的探讨
In this paper analysis of installation positions of the knee bracing fame is discussed.
本文针对隅撑的安装位置并且运用有限元方法对其进行弹塑性加载分析,总结出一些结论和设计建议。
Within the design of product,the installation position of manipulating device affects directly on the manipulating behavior of the operator and has extremely important significance on the design and evaluation of the installation position of manipulating element.
在产品设计中,操纵装置安装位置直接影响了操作者的操纵行为,对操纵元件安装位置的设计和评价具有十分重要的意义。
Aimed at this problem,a design method of the gas spring installation site based on the motion simulation is presented.
针对气弹簧安装位置设计的问题,首先初选气弹簧,利用两点法算出安装点的理论最佳位置,提出一种基于运动仿真的气弹簧安装位置设计方法,在数字化样机中对气弹簧进行干涉分析和运动仿真,从而使气弹簧安装位置的选择一次成功,并以大功率拖拉机前机罩的气弹簧安装设计为例,验证了该设计的可行性和实用性,对于其它气弹簧安装位置的设计有重要的参考价值。
The structure of bolter was designed,through the bolter installed location analysis,roadheader and link style of bolter and other important technology solve,designed a bolting machine on roadheader which can both drill tunnel side and top blot s hole.
对锚杆钻机的结构进行了设计,通过对掘进机与锚杆钻机之间的安装位置的分析及掘进机与锚杆钻机连接方式等关键技术的处理,设计一种既能够打巷道顶部锚杆孔、又能打侧帮锚杆孔的机载式锚杆钻机。
Road vehicles--Semi trailer fifth wheel mounting
GB/T13880-1992半挂牵引车牵引座的安装
seat with integral seat belt anchorages
设有原装安全带固定装置的座位
Install screws attaching seat function switch to seat trim panel.
安装连接座椅功能开关至座椅饰板的螺钉。
accessory drive pad
附件传动装置安装座
The lathe should be set on a firm base.
车床应安装在坚实的底座上。
flexible-mounted engine
安装在弹性座垫上的发动机
The frame or chassis on which panels of electrical equipment may be mounted.
可安装电气设备板的框架或底座。
Install the seatback in the vehicle.
在车辆里安装座椅背。
A receptacle, especially one mounted in a wall, that is connected to a power supply and equipped with a socket for a plug.
电源插座与电源相接并装备有为插头而设的基座的电源插座,尤指安装在墙上的
Reinstall the elbow into the base of the relief valve to hold the Air Gap Drain in place.
将弯头安装在安全阀的底座,将气隙排放装置固定住。
Install the main unit to the in-dash location, and the connection box under the navigator's seat, etc.
把主机安装到仪表板上。并把连接盒安装到副驾驶座的下面。
"Controllers may be supplied with painted steel floor mounting legs. For base mounting or stainless steel mounting legs, consult the Factory."
可提供配置涂漆钢地面安装支架的控制装置。如果需要底座安装或不锈钢安装支架,请工厂联系。
The switches and power sockets for fume hoods shall be placed on the outside of the fume hood.
所有的开关和插座都需安装在通风柜外部。
Installation Technologies of Preburied Prestressed Anchor Bolts of Wide Diameter Pin Roll Hinge Supports
预埋预应力锚栓的大直径销轴铰支座安装技术
On the Methods of the Plane Adjustment of Fitting Frame Lathe Bed Base
框架式床身底座安装水平调整方法的探讨
Supervision control point of laminated rubber bearing
板式橡胶支座施工安装的监理控制要点
Existing Problems and Solutions of Plate Rubber Support Installation
桥梁板式橡胶支座安装存在的问题及解决方案
skid-mounted pump unit
装在滑橇座上的泵装置
CopyRight © 2020-2024 优校网[www.youxiaow.com]版权所有 All Rights Reserved. ICP备案号:浙ICP备2024058711号