deposited seat是什么意思

网络释义

用法例句

Stress calculation and analysis on welding seat of stop valve;

截止阀焊接阀座的应力计算与分析

Wear resistant impact hardfacing flux-cored wire used in tool manufacture of shield machine;

盾构机刀具制造用耐磨耐冲击堆焊药芯焊丝的研究

Effect of alloy elements and heat treatment technology on microstructure and property of hardfacing metal for cold scissors;

冷剪刃堆焊金属的组织与性能

Field mobile welding machine for drilling tool hardfacing;

野外可移动式钻具耐磨带堆焊专机

Effect of welding material component on high frequency surfacing process;

焊料成分对高频堆焊性能的影响

Ultrasonic signal character and quality evaluation of Cu/steel surfacing weld;

铜钢堆焊接头的超声信号特征及质量评价

Development of special welding machine for inner surfacing welding of high-temperature cylinder;

高温圆筒内壁堆焊焊接专机的研制

Automatic surfacing welding method with equal thickness for circle plane;

一种圆环面等厚自动堆焊方法

Research on new technology of repairing rails tracks by surfacing welding;

铁路在线伤损钢轨堆焊修复新技术研究

Valves with threaded-in strength welded seats offer an additional level of safety against fugitive emissions.

带有螺纹旋进强度的焊接阀座能够为短时排放提供更高水平的安全性能。

Welded-in seat is Stellite 6 faced.

焊接连接阀座采用钨铬钴合金6阀座面。

Seat hardfaced with SS410 and seal welded.

配置410不锈钢和密封焊接的阀座硬面。

Seat ring is seal welded to eliminate leak path.

阀座环通过密封焊接，消除泄漏通道。

Welded-in seats hardfaced with Stellite 6.

钨铬钴合金6硬面的焊接装配阀座。

Reason Analysis and Treatment of Weld Crack in Water Drain Valve Base of Spiral Casing in Longtan Hydropower Station

龙滩电站蜗壳排水阀阀座焊接裂纹产生原因及处理

Analysis and treatment of welding crack of spiral case drain valve base

龙滩电站蜗壳排水阀阀座焊接裂纹原因分析及对策

Leaving the disc in a fully closed position firmly closed also prevents weld spatter from falling directly onto the mating faces of the seat and disc.

保持阀瓣处于完全关闭位置也能够避免焊花直接掉在阀座和阀瓣的连接面上。

Seats are hardfaced with SS410 and welded-in for lifetime service.

阀座用410不锈钢进行硬面，通过焊接装配延长使用寿命。

Warning: Avoid overheating when soldering - it could cause internal damage to seat area.

警告：在焊接时，要避免过热-过热会导致阀座区域受到内部损坏。

Leaving the valve in a fully closed position helps prevent weld spatter from falling directly onto the mating faces of the seats.

保持阀门处于完全关闭状态，有助于防止焊花飞溅直接落到阀座连接面上。

Apply heat with flame directed away from the center of the valve body. Excessive heat can harm the seats. After soldering, the packing nut may have to be tightened.

在用明火加热时不要直接施加在阀体中心上。过热可能损害阀座。焊接后，填料螺母可能需要紧固。

Assessing the safety of fully welded body pipeline ball valve

全焊接阀体管线球阀焊接接头的安全评估

"Face-to-face, centre-to-face, end-to-end and centre-to-end dimensions of valves--Buttwelding valves"

GB/T15188.1-1994阀门的结构长度对焊连接阀门

apply brazing wire or rod at point where tube enters valve socket.

将焊线或焊杆点在阀门里的管道套座上。

Silver Brazing Method: Apply brazing wire or rod at point where tube enters valve socket.

银钎焊法：将焊线或焊杆点在阀门里的管道套座上。

General purpose industrial valves--Flanged and butt-weld end steel ball valves

GB/T12237-1989通用阀门法兰和对焊连接钢制球阀

General purpose industrial valves-Flanged and butt-weld steel gate valves

GB/T12234-1989通用阀门法兰和对焊连接钢制闸阀