design note是什么意思

网络释义

用法例句

Detailed introduction is made from grouting design,calculation,construction method,matters deserving attention in construction,quality inspection and other aspects.

结合工程概况,提出采用渗透式注浆方式作为加固防护方案,对其注浆设计计算过程、施工工艺、施工注意事项、质量检查等方面进行了介绍,并对其施工效果进行了评价,以供类似工程参考借鉴。

The paper also briefiy introducd drilling and grouting design.

介绍采用地面打钻深孔注浆充填主、副井井壁后空硐,应用了深孔位防偏斜技术,深孔位套管技术等多顶新工艺、新技术,通过浆液高压挤压作用降低孔隙率,减少地层压缩,加固地层,防止井筒的突然破坏,文中对钻孔灌注浆设计进行重点介绍。

This paper introduced the ground pre-grouting design and the key technical measures of construction through an engineering practice, and summarized some useful experiences.

本文通过实例介绍了地面预注浆设计和施工关键技术措施,总结了提高注浆效率、改进“三同时”建井工艺的有益经验。

The liquid silica rubber(LSR) had unique physical performance,through the liquid silica rubber injection mold design example,analyzed several attention points in designing injection mold.

液体硅橡胶(LSR)具有独特的物理性能,通过液体硅橡胶注射模设计实例,分析了其注射模设计中应注意的几个问题。

In this article, the process of injection mold design using SolidWorks software were introduced.

主要介绍了用Solidworks软件进行注射模设计的一般步骤,并且结合鼠标外壳注射模设计的具体实例,介绍了利用Solidworks进行注射模设计的基本方法。

Taking injection mold design and mold cavity NC machining of the plastic shell as an example, stated the technology and step of mold designing and NC machining using CAD/CAM software in details.

以一塑料外壳注射模的设计和模具型腔的数控加工为例,较为详尽地讲述了运用CAD/CAM软件进行注射模设计和数控加工的工艺和步骤。

Design of Injection Mold with Auto-Stripping Inner and Outer Screw Mechanism By Oil Cylind

油缸式自动内外螺纹脱模注射模设计

Cellular Phone Outer Shell Injects the Mold Design and Application of CAD/CAE/CAM;

手机外壳注射模设计与CAD/CAE/CAM的应用

Design of Injection Mold for the Upper Clutch Coupling

基于CAE分析的上离合器注射模设计

Design of auto-stripping injection mould with parting-out in sequence and pin gate mechanism

顺序分型点浇口自动脱料注射模设计

Application of CAD/CAE Technology to Injection Mould Design

CAD/CAE技术在注射模设计中的应用

DESIGN OF INJECTION MOLD FOR THE AUTOMOBILE CONTROL PANEL FOR THE LEFT FRONT SWITCH

汽车左前开关控制面板的注射模设计

Design of Injection Mold of the Tee Pipe Based on Pro/E

基于Pro/E的三通管注射模设计

Design of Injection Mold for the HOLDER-GEL Part in CD Writer

刻录机中HOLDER-GEL零件的注射模设计

Design of Injection Mold to Magnetic Treat Instrument Based on CAE Technology

基于CAE技术的磁疗仪注射模设计

Design of the Injection Mould for Box Cover of Combined Switch Based on Pro/E

基于Pro/E的组合开关盒盖注射模设计

CAE-based design of injection mould for casing cover of hair dryer

基于CAE分析的风筒壳后盖注射模设计

Molding Process Analysis and Injection Mold Design for the Automobile Door Plate

汽车门板零件工艺分析和注射模设计

Pro/E based design of injection mold for T-Joint fittings

基于Pro/E三通管件注射模设计

Optimization of feed system and design of injection mould for automotive engine cover

汽车发动机罩盖浇注系统优化与注射模设计

Application of failure mode effects analysis in design of injection mould;

失效模式及后果分析在注射模设计中的应用

The injection molding of LCD shell and push button key in a mould

显示器壳体与按键同模成型注射模设计

UG/NX-based design of injection mould and mould flow analysis

基于UG/NX的洗发水瓶盖注射模设计与模流分析

The Model Stream Analyses a Software Injecting Model Application in Designing that in Monoblock

模流分析软件在壳体注射模设计中的应用